News

Maintenance points of WD120-23.5-1 worm gear reduc

25-09-03

WD120-23.5-1 is a single-stage worm gear reducer with a worm gear located below, a center distance of 120 mm, and a nominal speed ratio of approximately 23.5. It is suitable for situations that require high speed ratios, smooth transmission, and may have reverse self-locking; However, friction heating and high alignment requirements require strict lubrication and temperature rise management. Main

READ MORE
Detailed introduction to the structural features a

25-09-02

JBT type reducer frame is a common component used to support and connect reducers. The following is a detailed introduction about it: Model and specification: There are various models of JBT reducer frames, such as JBT2-B1 (X3)、JBT2-B2 (X4)、JBT3-B2 (X4)、JBT3-B3 (X5)、JBT4-B3、JBT5-B3-(X5)、JBT5-B4、JBT6-B4、JBT6-B5 (X8)、JBT7-B5 (X8)、JBT8-B6 (X9)、JBT9-B7 (X10) Wait. Structural characteristics: Th

READ MORE
What are the effects of noise and vibration level

25-09-02

The noise and vibration level standards have a significant impact on the performance and lifespan of FF157 hard tooth gear reducers, as follows: Impact on performance Transmission accuracy: Excessive noise and vibration levels usually indicate significant instability factors in the gear transmission process. If there are errors in gear meshing or misalignment of the shaft system, it will lea

READ MORE
What are the specific steps for handling the abnor

25-09-01

To deal with the abnormal noise of WHX210-50-I, it is recommended to follow the closed-loop process of "safe shutdown → operation record → initial inspection of the whole machine → lubrication and installation → transmission and bearings → reinstallation and trial operation → status monitoring", and prioritize locking the three high-frequency causes of oil level/quality, alignment and bearings, an

READ MORE
Maintenance method for NGW-S-113-90 planetary gear

25-09-01

The maintenance method of NGW-S-113-90 planetary gear reducer needs to be developed based on its structural characteristics and working environment, including lubrication management, mechanical component inspection, and operation status monitoring. The following are specific maintenance points: 1、 Daily maintenance (daily/shift) Running status monitoring Before starting: manually rotate the

READ MORE
What are the specific manifestations of gear damag

25-08-29

The specific manifestations of gear damage in SF67-YB3KW-52-M6 hard tooth reducer are as follows: Tooth surface wear: Scratches, pitting, peeling and other phenomena appear on the tooth surface, resulting in thinning of tooth thickness, deformation of tooth profile, and increased meshing clearance. As the wear intensifies, the dynamic load on the gear increases, and the vibration and noise will

READ MORE
What are the effects of noise and vibration level

25-08-29

The noise and vibration level standards have a significant impact on the performance and lifespan of FF157 hard tooth gear reducers, as follows: Impact on performance Transmission accuracy: Excessive noise and vibration levels usually indicate significant instability factors in the gear transmission process. If there are errors in gear meshing or misalignment of the shaft system, it will lea

READ MORE
What methods can be used to verify whether the con

25-08-28

Here are some methods to verify whether the concentricity adjustment of XWED-74-121-4 cycloidal pinwheel reducer is qualified: Dial gauge measurement method: Fix the magnetic gauge holder on the reducer shaft or motor shaft, and place the gauge head against the outer circular surface (radial) or end surface (axial) of the central axis. Manually rotate the shaft 360 ° and record the difference b

READ MORE
What safety precautions should be taken when adjus

25-08-28

When adjusting the concentricity of XWE84-7569 cycloidal pinwheel reducer, the following safety precautions should be noted: Equipment power-off: Before adjusting the concentricity, the power supply of the reducer must be cut off first, and the power switch must be locked or hung to prevent accidental power on during the adjustment process, which may cause personal injury or equipment damage.

READ MORE