News

How to determine whether the installation referenc

26-01-09

To determine whether the installation reference surface of FF78-Y4-4P-21.43-M1 reducer is flat, a method of tool inspection and fitting verification should be used, with precise steps that can be directly operated: 1. Prepare testing tools Select a frame level with an accuracy level of ≥ 0.02mm/m, a feeler gauge with an accuracy of 0.02mm, and a clean ruler (with a length not less than the d

READ MORE
How to check if the internal gear transmission sys

26-01-08

Check whether the internal gear transmission system of CJY180-63-3KW reducer is normal, combined with static inspection during shutdown and dynamic monitoring during operation. If necessary, disassemble and inspect the machine. The specific steps and judgment criteria are as follows: 1、 Static inspection during shutdown (no need to disassemble, quick initial judgment) 1. Appearance and seali

READ MORE
How to determine if CJY112-250-1.2KW shaft mounted

26-01-08

The key to determining whether the CJY112-250-1.2KW shaft mounted reducer requires additional maintenance depends on the working conditions and status. The following is the specific method of judgment: 1、 Additional maintenance judgment under special working conditions Heavy load/impact load conditions (such as metallurgical and mining equipment): Lubricating oil replacement cycle: If the e

READ MORE
What are the common errors during the installation

26-01-07

When installing the FAF37-0.75KW-8.2 reducer, common errors and corresponding precautions are as follows: 1. Coaxiality out of tolerance installation: Failure to calibrate the coaxiality between the motor and gearbox, as well as between the gearbox and the load, using a dial gauge resulted in forced coupling, causing the coupling to be biased, leading to bearing overheating and increased gear w

READ MORE
How to determine whether the installation referenc

26-01-07

To determine whether the installation reference surface of FF78-Y4-4P-21.43-M1 reducer is flat, a method of tool inspection and fitting verification should be used, with precise steps that can be directly operated: 1. Prepare testing tools Select a frame level with an accuracy level of ≥ 0.02mm/m, a feeler gauge with an accuracy of 0.02mm, and a clean ruler (with a length not less than the d

READ MORE
What are the precautions for adjusting the gasket

26-01-06

When adjusting the ZLY224-12.5-1 reducer gasket, it is important to pay attention to the following safety and operational points: 1、 Core principles of gasket adjustment Thickness matching: The thickness of the gasket needs to be adapted to the gear mesh clearance. When the wear is light, only adjust the thickness of S1. When the wear is heavy, adjust S1/S2 (driven gear side) and S3/S4 (drivin

READ MORE
How to solve the problem of high oil temperature i

26-01-06

The WPS60-20-A gearbox has high oil temperature due to excessive load, which can be systematically solved through the following steps: 1、 Core solutions 1. Adjust the load immediately Check if the motor current exceeds 110% of the rated value. If it is overloaded, optimize the production process or reduce the load. Avoid frequent starting and stopping (≤ 5 times per hour) to reduce imp

READ MORE
How to determine whether the lubricating oil of YC

26-01-05

To determine whether the lubricating oil of YCJ225/Y133M-7.5-B3 reducer needs to be replaced, the following methods can be used: 1、 Regular inspection Time cycle: Change the oil for the first time after running for 200 hours, and then adjust according to the running time: High load operation (over 10 hours per day): Replace every 3 months. Low load operation (≤ 10 hours per day): Repla

READ MORE
What are the specific operating steps of ZLY224-20

26-01-05

The specific steps for adjusting the gear machining method of ZLY224-20-1N reducer are as follows: 1. Gasket adjustment method Principle: Adjust the axial position of the gear and change the meshing clearance by increasing or decreasing the thickness of the gasket. Operation steps: (1) Disassemble the gearbox components and expose the gear set. (2) Measure the thickness of the origi

READ MORE