News

How to choose bearings suitable for parallel axis

25-09-23

The following is a selection guide for selecting bearings suitable for parallel axis F57-NA40-1.1KW gear reducers, combined with load characteristics, installation space, and operating requirements for comprehensive explanation: 1、 Core parameters for bearing selection Load characteristic analysis Radial load: Parallel axis gear reducers mainly bear radial loads, and deep groove ball bearin

READ MORE
Structural Design and Principle of WS120-60-II Wor

25-09-22

The following is a comprehensive analysis of the structural design and principle of WS120-60-II worm gear reducer: 1. Basic structure and transmission principle The WS120-60-II reducer adopts worm gear transmission, and its core structure includes: Worm: As an active component, it is usually designed with single or multiple helical teeth and made of quenched steel (such as 20CrMnTi) to impr

READ MORE
How long is the service life of WS210-41-V worm ge

25-09-22

The service life of WS210-41-V worm gear reducer is affected by various factors. Generally speaking, under normal use and maintenance conditions, its service life is usually around 5-10 years. But if the design is reasonable, the material selection is appropriate, and the maintenance is proper, its service life may also be longer, even up to 10 years or more. The following is an analysis of specif

READ MORE
How to install WB65-WD-29-1 micro cycloidal reduce

25-09-19

The installation of WB65-WD-29-1 micro cycloidal reducer can be carried out according to the following steps: Pre-installation preparation Environmental inspection: Ensure that the installation environment is dust-free, dry, with stable temperature, and away from vibration sources and strong magnetic field interference. Tool preparation: Prepare torque wrenches, hex screwdrivers, vernier ca

READ MORE
How to adjust the meshing clearance of WPS250-40-B

25-09-18

Priority should be given to using the method of "fine adjustment of worm axial gasket", following the closed-loop execution of "clarifying the target side clearance → measuring the initial value → fine adjusting in steps of 0.05~0.1mm → double checking with dial gauge/plug gauge and contact spot → confirming during trial operation". WPS250-40-B can be stably adjusted to the target value within the

READ MORE
What parts need to be replaced during maintenance

25-09-18

During routine maintenance and overhaul of WPS60-60-B, it is necessary to replace "lubricating oil, seals, and grease" on a periodic basis, and decide whether to replace core components such as "worm gear, bearings, gaskets, O-rings" based on the test results. Routine maintenance (parts must be replaced) Lubricating oil: replace the new machine after 300-500 hours; Replace every 1500-2000 hour

READ MORE
What factors will affect the machining accuracy of

25-09-17

The machining accuracy of the worm gear in CWO80-40-11 worm gear reducer is influenced by multiple factors, including: 1、 Materials and Manufacturing Processes Material characteristics: Worm gears are usually made of carbon steel or alloy steel (such as 40Cr), and their hardness and wear resistance after quenching and tempering heat treatment directly affect the accuracy of the tooth surface.

READ MORE
What impact does the flatness error of the NGW-L92

25-09-17

The flatness error of the NGW-L92-25 planetary gearbox base can indirectly or directly shorten its service life by affecting the three core dimensions of gearbox installation accuracy, stress state, and motion stability. The specific influencing mechanism can be decomposed into the following four key aspects, and the larger the error, the more significant the impact: 1、 Disrupting the neutrality

READ MORE
How to determine if the NGW-L51 planetary gearbox

25-09-16

To determine whether the NGW-L51 planetary gearbox is installed properly, it is necessary to start from three core dimensions: mechanical fit accuracy, stress state, and operational stability. Combined with installation specifications and measured data, comprehensive verification should be carried out to avoid problems such as abnormal noise, vibration, and shortened service life caused by install

READ MORE