• 
  How to avoid screw loosening during the operation

  25-06-10

  Here are some methods to avoid screw loosening during the operation of ZLY560-25-I hard tooth reducer: Choose appropriate screws and nuts: Ensure that the specifications of the screws and nuts are correct, the fit is tight, the quality is good, and they have sufficient corrosion resistance and wear resistance to reduce looseness caused by long-term use. Use anti loosening device: Spring w

  READ MORE
• 
  What methods can be used to reduce the resistance

  25-06-09

  Here are some methods to reduce the resistance of the lubrication system of ZFY315-140-II gearbox: Inspect and maintain lubrication system components: Regularly inspect lubrication pumps, filters, oil tanks, pipelines, and other components to ensure they are intact and free from leaks or blockages. For clogged filters, clean or replace the filter element in a timely manner to ensure smooth f

  READ MORE
• 
  What advanced technologies or methods can be used

  25-06-09

  Here are some advanced technologies and methods that can be used for maintenance of GRF97-7.5KW-25.03 gearbox: Oil monitoring technology Online oil analysis system: Install oil sensors on the reducer to monitor real-time parameters such as temperature, pressure, viscosity, density, dielectric constant, moisture, metal wear particles, conductivity, etc. of the lubricating oil. By analyzing th

  READ MORE
• 
  lications can the KAT57-1.5KW-19.34 hard gear surf

  25-06-06

  KAT57-1.5KW-19.34 hard tooth surface reducer can be applied in the following scenarios: Metallurgical industry: used to drive metallurgical equipment, such as small rolling mills, mixers, conveyors, etc., to help these devices operate at appropriate speeds, meet production process requirements, and withstand large loads. Mining field: Equipment that can be used for ore screening, crushing, a

  READ MORE
• 
  KAT127-54.07-22KW gear reducer model meaning and c

  25-06-06

  The meaning and characteristics of the KAT127-54.07-22KW reducer model are as follows: Model meaning: KAT: Indicates that the type of reducer is a helical bevel gear reducer. Among them, K represents a bevel gear reducer, A may represent a specific design or structural feature, and T usually indicates that the reducer has a three-stage transmission structure. 127: Represents the base numb

  READ MORE
• 
  How to address the abnormal noise issue with the b

  25-06-05

  To solve the abnormal bearing noise problem of the DCY560-22.4-3N reducer with hard tooth surface, the following aspects can be taken into account: Check the lubrication condition Ensure the oil level is normal: Check the oil level of the gearbox. If the oil level is too low, add lubricating oil that meets the requirements to the appropriate level. Ensure good oil quality: Regularly check

  READ MORE
• 
  What type of lubricating oil should be used for th

  25-06-05

  P3KA17 planetary gearbox can usually use medium load industrial gear oil, and the specific model needs to be determined according to the ambient temperature and output shaft speed ： When the ambient temperature is between -10 ℃ and 15 ℃, and the output shaft speed is higher than 100 revolutions per minute, 68 gear oil can be selected; If the output shaft speed is lower than 100 revolutions per

  READ MORE
• 
  When repairing the BLD8-35-45KW cycloidal reducer

  25-06-04

  When repairing the output shaft of BLD8-35-45KW cycloidal reducer, the following issues should be noted: Safety issue: Before maintenance, it is necessary to cut off the power supply and set up a warning sign prohibiting opening at the switch to prevent accidental power on from causing safety accidents. Dismantling and installation Standardized disassembly: Disassemble relevant components

  READ MORE
• 
  The sealing structure of the ZQD850-317-28 soft ge

  25-06-04

  The common sealing structures and characteristics of ZQD850-317-28 reducer with soft tooth surface are as follows: Sealing of shaft extension Felt ring sealing: using a rectangular section felt ring embedded in a trapezoidal groove to exert a compressive effect on the shaft, thereby preventing lubricating oil leakage and external impurities, dust, etc. from entering the bearing chamber. The

  READ MORE

CATEGORIES