• 
  How to determine whether the rust inhibitor is com

  26-01-02

  The key to determining whether the rust inhibitor is compatible with KA107-103-YVP7.5KW gearbox gear oil is whether they can work together without affecting lubrication and rust prevention effects. Here are a few key points that have been sorted out: 1、 Check if the base oil type matches Mineral oil-based gear oil: suitable for using mineral oil-based rust inhibitors, with good compatibility

  READ MORE
• 
  How to correctly apply rust inhibitor to KAB97-186

  26-01-02

  The key to rust prevention for KAB97-186.52-5.5KW reducer is to choose the right method, use the right product, and operate it properly. The following are specific steps and precautions: 1、 Choose the right rust inhibitor Check the environment: If the gearbox is indoors, choose water-based rust inhibitor (environmentally friendly) or rust proof oil (moisture-proof); If outdoors, use solvent

  READ MORE
• 
  Lubrication System Structure of KAB107-90.96-YEJ11

  25-12-31

  The lubrication system structure of KAB107-90.96-YEJ11KW gear reducer mainly includes the following key parts: 1. Oil pump: responsible for extracting lubricating oil from the oil tank and delivering it to the components that require lubrication, such as gears and bearings. 2. Oil cooler: used to reduce the temperature of lubricating oil and prevent the lubrication effect from being affected

  READ MORE
• 
  What are the advantages and disadvantages of the l

  25-12-31

  The advantages of the lubrication system for KA77-20-YEJ3-M1 gear reducer are as follows: 1. Minimalist structure, extremely low failure rate, and low maintenance cost No external vulnerable parts such as oil pumps, pipelines, valves, etc., relying solely on self operation to supply oil, without power failure, pipeline blockage, oil leakage and other problems; Only regular oil changes and oi

  READ MORE
• 
  How to straighten the cycloidal gear of XWD9170-87

  25-12-30

  After heat treatment, the cycloidal gear is straightened, and the core is to choose cold or hot calibration according to the degree of deformation and material characteristics, and strictly control the process details. The specific method is as follows: 1、 Selection of straightening methods Cold straightening (suitable for slight deformations) Apply reverse pressure to the bent part using

  READ MORE
• 
  How to repair the deformed cycloidal gear of XWD81

  25-12-30

  The deformation repair of XWD8185B-87-7.5KW cycloidal gear (commonly GCr15 vacuum quenching, 20CrMnTi carburizing quenching) should first detect and screen out cracks, and then classify the treatment according to the deformation level and defect type: mild/moderate, mainly straightening+stability+grinding/wire cutting compensation; Severe/tooth profile distortion is mainly repaired by grinding/wir

  READ MORE
• 
  How does the noise performance of hard tooth surfa

  25-12-29

  There are indeed differences in the noise performance of hard tooth and soft tooth reducers at different speeds. Let me help you sort out the key points: 1、 Hard tooth surface reducer At high speeds: Noise is usually lower because hard toothed gears have high machining accuracy, can withstand larger loads and higher speeds, operate more smoothly, and produce less noise due to friction and im

  READ MORE
• 
  How to choose between hard tooth surface reducer a

  25-12-29

  The key to choosing a hard tooth or soft tooth reducer depends on the actual working conditions and requirements. The following are the core differences and selection points between hard tooth surface and soft tooth surface reducers: 1、 Comparison of core differences 1. Tooth surface hardness and material Hard tooth surface: The gear has high hardness (>350HB or 38HRC) and is commonly mad

  READ MORE
• 
  How to determine if there is minor damage to the l

  25-12-26

  To determine if there is any minor damage to the lip of the bearing seal of the FAF67D100M4/61.07/M1/0 reducer, the following steps can be followed: 1、 Appearance inspection Observing the lips: Carefully inspect the lips with a magnifying glass or endoscope for cracks, burrs, or localized wear. Check the sealing surface: Confirm whether the sealing surface is evenly adhered, whether there

  READ MORE

CATEGORIES