• 
  How to check if the seal matches the cleaning part

  25-11-12

  When installing new seals for the WPDA80-60-0.75KW gearbox, double verification is required from both the compatibility of seal specifications and component cleanliness to ensure that the seals are compatible with the installation position and free of impurities that interfere with the sealing effect. The specific inspection method is as follows: 1、 Check the specification matching between the se

  READ MORE
• 
  How to determine the wear condition of the cycloid

  25-11-11

  To determine the wear condition of the cycloidal gear and needle gear housing of this model reducer, the core is to comprehensively judge the three-dimensional degree through appearance inspection, clearance measurement, and operation status observation, and accurately identify the degree of wear: 1. Visual inspection of appearance If the tooth tip becomes dull, or if grooves or bumps appear o

  READ MORE
• 
  How to correctly install the new XLED85-3481-1.1KW

  25-11-11

  The correct installation of the cycloidal gear and needle gear housing of this model reducer requires precise alignment, smooth assembly, compliant clearance, and secure fastening to avoid component damage and transmission failures. The steps are as follows: 1. Preparation before installation Confirm that the new part model matches the reducer, that there are no cracks or deformations in the c

  READ MORE
• 
  How to choose the appropriate lubricating grease w

  25-11-10

  Choose TY140-71-5.5KW reducer bearing grease that matches the bearing operating conditions (load, temperature, speed), with priority given to lithium based or composite lithium based grease. The key indicators should meet the requirements of "needle penetration 220-250, drop point ≥ 180 ℃, anti-wear extreme pressure grade ≥ EP2". 1、 Core selection criteria Suitable load and speed: The bearings

  READ MORE
• 
  Can you introduce the amount of lubricating grease

  25-11-10

  According to the model parameters of TY80-14-1.5KW reducer bearings (outer diameter 80mm, width 14mm), the lubricating grease filling amount can refer to the following standards and methods: 1、 Calculation of refueling volume General formula: Lubricating grease filling amount (G)=0.005 × bearing outer diameter (D) × bearing width (B) Substitute data: G=0.005 × 80 × 14=5.6g Sealed bearings

  READ MORE
• 
  What is the high temperature warning value set for

  25-11-08

  The setting of high temperature warning values for FAF77-2.2KW-25.47-M5 gear reducer needs to be combined with its structural characteristics and working environment. The core parameters are as follows: 1、 Temperature warning threshold setting Bearing temperature warning value Under normal operating conditions, it is recommended to set the temperature to 75 ℃ (Level 1 warning). If the tempe

  READ MORE
• 
  How to check and maintain FAF37-B0.55-4P-47.02-M3-

  25-11-08

  Regarding the FAF37-B0.55-4P-47.02-M3-270 gearbox, inspection and maintenance should revolve around the four core areas of "lubrication, heat dissipation, load, and component status" to effectively prevent high temperature issues. 1、 Core Inspection: Pre check for High Temperature Hazards Regular inspections should cover the following key dimensions. It is recommended to conduct regular inspecti

  READ MORE
• 
  How to determine if the cooling fan of FAF67-4.21-

  25-11-08

  To determine whether the cooling fan of FAF67-4.21-4KW reducer is operating normally, it is necessary to combine mechanical characteristics and multidimensional detection methods. The specific steps are as follows: 1、 Basic observation and auditory detection Observation of operating status After starting the gearbox, directly observe whether the fan blades are rotating at a constant speed (

  READ MORE
• 
  How to determine if the worm gear of WPWA155-50-B

  25-11-08

  To determine whether the worm gear of WPWA155-50-B reducer is aligned with the teeth (i.e. whether the meshing state is normal), the following comprehensive inspection methods should be used: 1、 Appearance and contact mark inspection Red Dan Powder Coloring Method Normal state: The contact area should be located in the middle of the tooth surface (near the pitch circle), with an area of ≥ 7

  READ MORE

CATEGORIES