• 
  How to determine if the installation of DCYK400-63

  25-07-18

  To determine whether the DCYK400-63-1N hard tooth reducer is installed correctly, the following aspects can be taken into account: Installation foundation and fixing inspection: The reducer should be firmly installed on a stable foundation or base. Check if the installation foundation is flat, sturdy, and free from looseness or vibration. If the foundation is unreliable, vibration and noise wil

  READ MORE
• 
  How to optimize the structural design of the TY80-

  25-07-17

  Optimizing the structural design of TY80-114-1.5KW reducer to reduce vibration can be achieved by starting from aspects such as gear system, bearings and shaft system, and box structure. The specific methods are as follows: Optimization of gear system Using helical gears: Replace spur gears with helical gears, and recommend helical gears with a helix angle of ≥ 15 °. This can increase the nu

  READ MORE
• 
  What tools are needed for the major overhaul of th

  25-07-17

  When overhauling the K87-15KW-9.96 gearbox, various tools are required, as follows: Tools: Dismantling tool: Puller is used to dismantle pulleys, gears, bearings, etc; The bearing press can assist in disassembling and installing bearings; Copper bars are used for tapping, disassembling, or installing components to avoid damaging them; Top wire or pry bar can be used to separate end caps.

  READ MORE
• 
  When installing the ZQ400 soft gear surface reduce

  25-07-16

  When installing the ZQ400 soft tooth surface reducer, the coaxiality between the motor shaft and the reducer input shaft can be checked by the following methods: Steel ruler and plug gauge inspection method: Place the steel ruler on the large outer circle parallel to the axis of the coupling, making it at a 90 ° angle to the axis, and continuously inspect three points. If the gap between the st

  READ MORE
• 
  What are the advantages and disadvantages of ZS85-

  25-07-16

  The advantages of ZS85-160-III soft tooth surface gear reducer include smooth transmission, strong adaptability, and low manufacturing and maintenance costs. The main disadvantages are limited load-bearing capacity and short service life, as follows: advantage: Smooth transmission and low noise: Soft tooth surface reducers usually use involute helical cylindrical gear transmission, which mak

  READ MORE
• 
  What are the precautions for adjusting the speed r

  25-07-15

  When adjusting the speed ratio of ZL850-20 soft tooth surface reducer, the following precautions should be taken: Confirm the parameters and specifications of the gearbox: Before adjusting the speed ratio, it is necessary to first confirm whether the speed ratio, rated torque, input power and other parameters of the gearbox meet the actual needs, to ensure that the adjusted speed ratio can enab

  READ MORE
• 
  How to determine the optimal gear ratio for the ZS

  25-07-15

  To determine the optimal speed ratio of ZS60 cylindrical gear reducer, it is necessary to comprehensively consider factors such as load demand, motor speed, and transmission efficiency. The specific methods are as follows: Calculate based on load torque and speed requirements: Firstly, clarify the required output torque (T) and output speed (n2) of the working mechanism, as well as the rated po

  READ MORE
• 
  What faults can occur in ZQD500+150-280 high trans

  25-07-14

  Insufficient installation accuracy can lead to abnormal vibration and noise, increased wear of gears and bearings, reduced transmission efficiency, oil leakage, and oscillation in ZQD500+150-280 high transmission ratio reducers, as follows: Abnormal vibration and noise: Insufficient installation accuracy, such as gear shafts not being parallel or the coaxiality of the reducer and motor not meet

  READ MORE
• 
  What details should be paid attention to during th

  25-07-14

  The installation process of ZQD large transmission ratio reducer requires attention to multiple details to ensure its normal operation and service life, as follows: Preparation before installation Check the components: Carefully inspect all parts of the reducer, including gears, bearings, seals, etc., to ensure that the model and specifications of the reducer match the actual requirements, a

  READ MORE

CATEGORIES