• 
  How to determine whether the cycloidal gear of the

  25-11-21

  To determine whether the cycloidal gear of the cycloidal pinwheel reducer needs to be replaced, four key signals should be considered: wear and deformation, abnormal operation, failure marks, and meeting the service life standards. If any key problem occurs, it needs to be replaced. 1. Visual inspection: wear and deformation The tooth surface shows obvious pitting, peeling, angular collapse, o

  READ MORE
• 
  Why should the temperature of the heating and dryi

  25-11-21

  The heating and drying temperature of DCY gear reducer is controlled at 60-80 ℃, which is a scientific range based on the characteristics of its core components such as internal lubricating oil, seals, metal structural components, and drying efficiency. It can efficiently remove internal moisture and avoid damage to the equipment during the drying process. The specific reasons are as follows: E

  READ MORE
• 
  How to determine whether the vibration fault of WP

  25-11-20

  Core conclusion: To determine whether the vibration fault of WPDO175-40-A worm gear reducer is caused by insufficient installation accuracy, the core is to look at the correlation between vibration and installation related parameters. Through three steps of "appearance inspection+vibration characteristic analysis+targeted verification", accurate judgment can be made. 1. First, conduct a visual an

  READ MORE
• 
  What abnormal vibrations can be caused by lubricat

  25-11-20

  The lubrication system failure of WPDKS175-50-50-7.5KW worm gear reducer can cause three types of abnormal vibrations: mid low frequency irregular vibration, meshing impact vibration, and high-frequency friction vibration, often accompanied by temperature and noise synchronous abnormalities. 1. Irregular vibration at medium and low frequencies (insufficient lubrication/abnormal oil level) When

  READ MORE
• 
  How often should the fastening screws of P2SA21 pl

  25-11-19

  There is currently no publicly available standard for the inspection cycle of exclusive fastening screws for P2SA21 planetary gearboxes. However, based on the general maintenance specifications for planetary gearboxes and their high probability of adaptation to industrial transmission scenarios, the inspection frequency can be determined according to three dimensions: initial installation, regular

  READ MORE
• 
  What are the vulnerable parts of P2SA26 planetary

  25-11-19

  There is no publicly available list of vulnerable parts for P2SA26 planetary gearboxes, but the core transmission structure and force logic of planetary gearboxes are universal. Based on the common fault patterns of this type of equipment, their vulnerable parts can be divided into three categories: core transmission components, sealing and protective components, and auxiliary fastening components

  READ MORE
• 
  How to regularly check the levelness of the motor

  25-11-18

  Regular inspections should follow the principle of "fixed cycle+standard process+precise detection", with a focus on monitoring the levelness of the base and axis, while simultaneously checking the coaxiality in conjunction to avoid cumulative deviation affecting the transmission. 1、 Determine the inspection cycle Daily inspection, once a week, quickly checks for vibration and abnormal noise d

  READ MORE
• 
  Recommend some application cases of WHC200-16-IV c

  25-11-17

  In WHC200-16-IV, 200 represents the center distance, 16 is the speed ratio, and IV corresponds to a specific assembly form. It has the characteristics of strong load-bearing capacity, high operating efficiency, and good stability. The maximum input power is 26KW and the maximum output torque is 2600N. m. It is suitable for heavy-duty deceleration scenarios in multiple fields such as metallurgy, mi

  READ MORE
• 
  What should be noted for the installation and main

  25-11-17

  The installation core of WHC210-50-4F worm gear reducer is to ensure coaxiality and firm fixation. The key to maintenance lies in lubricating oil management and component inspection. Specific precautions are as follows: 1、 Installation precautions Preparation before installation: Check the appearance of the reducer for any bumps or cracks in the castings, and confirm that the input and output

  READ MORE

CATEGORIES