• 
  Can you introduce the amount of lubricating grease

  25-11-10

  According to the model parameters of TY80-14-1.5KW reducer bearings (outer diameter 80mm, width 14mm), the lubricating grease filling amount can refer to the following standards and methods: 1、 Calculation of refueling volume General formula: Lubricating grease filling amount (G)=0.005 × bearing outer diameter (D) × bearing width (B) Substitute data: G=0.005 × 80 × 14=5.6g Sealed bearings

  READ MORE
• 
  What is the high temperature warning value set for

  25-11-08

  The setting of high temperature warning values for FAF77-2.2KW-25.47-M5 gear reducer needs to be combined with its structural characteristics and working environment. The core parameters are as follows: 1、 Temperature warning threshold setting Bearing temperature warning value Under normal operating conditions, it is recommended to set the temperature to 75 ℃ (Level 1 warning). If the tempe

  READ MORE
• 
  How to check and maintain FAF37-B0.55-4P-47.02-M3-

  25-11-08

  Regarding the FAF37-B0.55-4P-47.02-M3-270 gearbox, inspection and maintenance should revolve around the four core areas of "lubrication, heat dissipation, load, and component status" to effectively prevent high temperature issues. 1、 Core Inspection: Pre check for High Temperature Hazards Regular inspections should cover the following key dimensions. It is recommended to conduct regular inspecti

  READ MORE
• 
  How to determine if the cooling fan of FAF67-4.21-

  25-11-08

  To determine whether the cooling fan of FAF67-4.21-4KW reducer is operating normally, it is necessary to combine mechanical characteristics and multidimensional detection methods. The specific steps are as follows: 1、 Basic observation and auditory detection Observation of operating status After starting the gearbox, directly observe whether the fan blades are rotating at a constant speed (

  READ MORE
• 
  How to determine if the worm gear of WPWA155-50-B

  25-11-08

  To determine whether the worm gear of WPWA155-50-B reducer is aligned with the teeth (i.e. whether the meshing state is normal), the following comprehensive inspection methods should be used: 1、 Appearance and contact mark inspection Red Dan Powder Coloring Method Normal state: The contact area should be located in the middle of the tooth surface (near the pitch circle), with an area of ≥ 7

  READ MORE
• 
  What are the performance parameters of the NGW123-

  25-11-05

  HT250 is a pearl shaped gray cast iron. When the NGW123-500 planetary gear reducer base is made of this material, its performance parameters are as follows: 1. Chemical composition: Carbon content is 3.16% -3.30%, silicon content is 1.79% -1.93%, manganese content is 0.89% -1.04%, sulfur content is 0.094% -0.125%, and phosphorus content is 0.120% -0.170%. 2. Physical properties Density: G

  READ MORE
• 
  How to perform performance verification after crac

  25-11-05

  The performance verification of the NGW31-11-9 planetary gear reducer base after cracking repair is to confirm that the strength of the repaired area meets the standard, the equipment runs stably, and there is no crack recurrence or functional abnormality. It needs to be completed through three steps: "static testing+dynamic testing+load verification". 1. Static performance verification (performe

  READ MORE
• 
  When does the XWD4-17-1.5KW cycloidal pinwheel red

  25-11-04

  The core criterion for replacing lubricating oil in XWD4-17-1.5KW cycloidal pinwheel reducer is "time cycle+oil state+working condition intensity". If any condition is met, it needs to be replaced to avoid component wear caused by lubrication failure. 1、 Fixed time/operating cycle replacement (basic standard) First use: The new gearbox must be replaced after running for 200-300 hours to remove

  READ MORE
• 
  Where is the oil level indicator for XWD6-29-7.5 c

  25-11-04

  The oil level indicator of XWD6-29-7.5 cycloidal pinwheel reducer is usually located on the side or top of the box, and the specific position and inspection method are as follows: 1. Type of oil level indicator Cycloid pinwheel reducers often use transparent oil gauges (oil mirrors) or built-in oil dipsticks as oil level indicators. Transparent oil gauges are commonly used in small and medium-

  READ MORE

CATEGORIES