• 
  How to set the load and speed for the operation te

  25-08-20

  During the operation test of KBA107 gearbox, the load and speed settings need to be determined based on the rated parameters of the gearbox and relevant testing standards. Here are specific instructions: Speed setting: The input speed of KBA107 reducer is usually related to the speed of the matched motor, and the common 4-pole motor has a rated speed of 1400 revolutions per minute. When running

  READ MORE
• 
  How to operate the on-site balancing method in the

  25-08-19

  The on-site balancing method in the solution to abnormal vibration of ZJY212-20-S shaft mounted reducer is as follows: 1. Preparation work: Tools and equipment: Prepare vibration analyzer, weighing block (various specifications), electronic phase meter, wrench, marker pen, safety lock, etc. Safety measures: Stop the machine and cut off the power supply, lock and tag it, and confirm that t

  READ MORE
• 
  What other factors besides quenching temperature a

  25-08-19

  In addition to quenching temperature and holding time, the following factors also affect the hardness of ZLY140-20-2 reducer gears: Gear materials: The basic hardness of gears varies among different materials. Common gear materials include high-strength alloy steel, cast steel, cast iron, etc. Among them, high-strength alloy steel has excellent mechanical and wear resistance properties and can

  READ MORE
• 
  How to determine if the lubrication system of B3SV

  25-08-18

  To determine whether the lubrication system of B3SV05-25-D high-power industrial gearbox is working properly, the following aspects can be taken into account: pressure monitoring Observing the oil pressure gauge: Under normal circumstances, the pressure of lubricating oil is generally maintained at 0.2-0.5MPa. Pressure sensors are installed at the inlet of the gearbox and the outlet of the o

  READ MORE
• 
  How to further optimize the gear structure of B3SH

  25-08-18

  To further optimize the gear structure of B3SH17-45 industrial gearbox to improve transmission stability, the following aspects can be taken into consideration: Gear parameter optimization Shape modification design: Drum shaped teeth can be used for slight modification along the tooth width direction to compensate for shaft deformation, installation errors, and stress concentration at the to

  READ MORE
• 
  What lubricating grease is generally used for the

  25-08-15

  The selection of gear and bearing lubricating grease for needs to consider factors such as working conditions, load, and speed. Here are some common grease recommendations: Great Wall brand reducer lubricating grease: It is made by thickening refined mineral oil with lithium soap of hydroxy fatty acids and refining it with extreme pressure anti-wear additives. It is a high-performance semi flu

  READ MORE
• 
  How to determine the amount of lubricating grease

  25-08-15

  The amount of lubricating grease for R67-113.94-0.75KW gearbox can usually be determined according to the following methods: Refer to the manufacturer's guide: The user manual or technical documentation provided by the gearbox manufacturer will clearly indicate the required amount of lubricating grease or oil level range for a specific model of gearbox, which is the primary basis for determinin

  READ MORE
• 
  How to choose the right seal for a TY115-18-7.5KW

  25-08-14

  Select the sealing components suitable for TY115-18-7.5KW hard tooth surface gear reducer. The specific selection method is as follows: Considering working temperature: If the working temperature of TY115-18-7.5KW hard tooth surface gear reducer is between -30 ℃ and 120 ℃, nitrile rubber (NBR) material seals such as nitrile skeleton oil seals can be selected, which have high cost-effectiveness

  READ MORE
• 
  What are the safety precautions to be taken when c

  25-08-13

  When checking for loose screws in the ZSY160-40-1 hard tooth reducer, special attention should be paid to the following safety precautions: do your homework Disconnect power supply: Before inspection, it is necessary to disconnect the power supply of the gearbox and ensure that the power switch is locked or hung to prevent accidental power on and personal injury. Wear protective equipment

  READ MORE

CATEGORIES