• 
  How to use L-CKE/P series special CWU280-60-II wor

  25-10-14

  1、 Selection and Characteristics of Lubricating Oil L-CKE/P series worm gear oil is specially designed for heavy-duty worm gear transmission with steel copper matching. It contains extreme pressure and anti-wear additives (such as sulfur and phosphorus compounds), which can effectively reduce the friction coefficient and prevent tooth surface bonding. The viscosity grade needs to be selected ac

  READ MORE
• 
  How to determine whether the WPKS70-40 worm gear r

  25-10-13

  To determine whether the WPKS70-40 worm gear reducer needs maintenance, the following key indicators need to be comprehensively tested: 1、 Appearance and sealing inspection Oil leakage phenomenon Check for oil stains on the gearbox housing, shaft seal, and mating surface. Minor oil leakage can be solved by replacing the seal, but if the oil leakage is frequent and accompanied by a rapid decre

  READ MORE
• 
  What is the difference between standard speed rati

  25-10-13

  The main differences between standard speed ratio reducers and non-standard speed ratio reducers are reflected in design flexibility, application scenarios, and production processes. The specific comparison is as follows: 1、 Speed ratio range and design standards 1. Standard speed ratio model The speed ratio range is fixed and has strong universality. For example, the standard speed ratio o

  READ MORE
• 
  How to prevent lubrication system failure of BWY92

  25-10-11

  To prevent the lubrication system failure of BWY9205-87-11KW cycloidal pinwheel reducer, a systematic prevention mechanism should be established around the four core links of "oil management, sealing protection, daily inspection, and standardized operation" to avoid the risk of lubrication failure from the source. The specific steps can be divided into the following six key steps: 1、 Strictly c

  READ MORE
• 
  What are the reasons for abnormal temperature rise

  25-10-11

  The causes of abnormal temperature rise in ZLY450-20-1 hard tooth gear reducer (usually normal operating temperature ≤ 80 ℃, exceeding this range or excessive temperature rise rate are all abnormal) can be investigated from four core factors: lubrication system, mechanical transmission, installation and operation, and environmental conditions. The specific reasons are as follows: 1、 Lubrication

  READ MORE
• 
  What are the steps required to replace the P3SA11

  25-10-10

  The following are the general steps for replacing the P3SA11 planetary gearbox filter: 1. Preparation work: Confirm that the gearbox has stopped running and cut off the power to ensure safe operation. Prepare the necessary tools such as wrenches, screwdrivers, etc., as well as new filter cartridges and seals. Place an oil drum under the gearbox to collect the discharged lubricating oil

  READ MORE
• 
  What are the precautions when disassembling and in

  25-10-10

  When disassembling and inspecting the WPKA100-60-A worm gear reducer, the following key points should be noted, combined with professional standards and practical experience: 1、 Safety preparation and tool selection Power outage and warning: The power must be cut off and a warning sign must be hung to ensure that the equipment completely stops running Special tool usage: Disassembling beari

  READ MORE
• 
  Introduction to the possible causes of WB100-D-23-

  25-10-09

  There are many reasons why the WB100-D-23-0.55KW micro cycloidal reducer may malfunction, and the following are some common factors: 1. Lubrication issues Insufficient lubrication: Insufficient lubricating oil can cause increased friction between components, resulting in poor protection and heat dissipation, accelerating wear and leading to malfunctions such as gear wear and bearing damage.

  READ MORE
• 
  How to replace the lubricating grease of WB1285-LD

  25-10-09

  There are usually some general standards for the replacement cycle and method of lubricating grease for micro cycloidal reducers, but specific reference should also be made to the product manual. The following is the relevant content about the replacement of lubricating grease for WB1285-LD-2065-0.37KW/4 micro cycloidal reducer: replacement cycle General situation: According to common specific

  READ MORE

CATEGORIES