• 
  Will the drying method affect the performance and

  25-11-13

  Under the standard operation of 60-80 ℃, the drying method will not have a negative impact on the performance of DCY315-35.5-1 hard tooth reducer, but can protect the equipment through dehumidification; If the temperature is out of control or operated improperly, it may cause local damage. 1. No negative impact under standardized operation Hard toothed gears undergo carburizing and quenching t

  READ MORE
• 
  What are the contents of the safety operation spec

  25-11-13

  The DCY355-50-2S reducer drying method safety operation specification revolves around four dimensions: temperature control, process monitoring, safety protection, and equipment protection, ensuring efficient drying without damaging the equipment. 1、 Preparation before operation (safety foundation) Stop the machine, cut off the power and hang a warning sign. Wait for the gearbox to cool down to

  READ MORE
• 
  How to avoid affecting the worm gear when replacin

  25-11-12

  When replacing the sealing components of the WPDA250-30-A gearbox, it is necessary to follow three key points: standardizing the operating procedures, protecting the core transmission components, and controlling the disassembly and assembly accuracy, in order to avoid abnormal meshing of the worm gear caused by external collision, position deviation, or contamination. The specific measures are as

  READ MORE
• 
  How to check if the seal matches the cleaning part

  25-11-12

  When installing new seals for the WPDA80-60-0.75KW gearbox, double verification is required from both the compatibility of seal specifications and component cleanliness to ensure that the seals are compatible with the installation position and free of impurities that interfere with the sealing effect. The specific inspection method is as follows: 1、 Check the specification matching between the se

  READ MORE
• 
  How to determine the wear condition of the cycloid

  25-11-11

  To determine the wear condition of the cycloidal gear and needle gear housing of this model reducer, the core is to comprehensively judge the three-dimensional degree through appearance inspection, clearance measurement, and operation status observation, and accurately identify the degree of wear: 1. Visual inspection of appearance If the tooth tip becomes dull, or if grooves or bumps appear o

  READ MORE
• 
  How to correctly install the new XLED85-3481-1.1KW

  25-11-11

  The correct installation of the cycloidal gear and needle gear housing of this model reducer requires precise alignment, smooth assembly, compliant clearance, and secure fastening to avoid component damage and transmission failures. The steps are as follows: 1. Preparation before installation Confirm that the new part model matches the reducer, that there are no cracks or deformations in the c

  READ MORE
• 
  How to choose the appropriate lubricating grease w

  25-11-10

  Choose TY140-71-5.5KW reducer bearing grease that matches the bearing operating conditions (load, temperature, speed), with priority given to lithium based or composite lithium based grease. The key indicators should meet the requirements of "needle penetration 220-250, drop point ≥ 180 ℃, anti-wear extreme pressure grade ≥ EP2". 1、 Core selection criteria Suitable load and speed: The bearings

  READ MORE
• 
  Can you introduce the amount of lubricating grease

  25-11-10

  According to the model parameters of TY80-14-1.5KW reducer bearings (outer diameter 80mm, width 14mm), the lubricating grease filling amount can refer to the following standards and methods: 1、 Calculation of refueling volume General formula: Lubricating grease filling amount (G)=0.005 × bearing outer diameter (D) × bearing width (B) Substitute data: G=0.005 × 80 × 14=5.6g Sealed bearings

  READ MORE
• 
  What is the high temperature warning value set for

  25-11-08

  The setting of high temperature warning values for FAF77-2.2KW-25.47-M5 gear reducer needs to be combined with its structural characteristics and working environment. The core parameters are as follows: 1、 Temperature warning threshold setting Bearing temperature warning value Under normal operating conditions, it is recommended to set the temperature to 75 ℃ (Level 1 warning). If the tempe

  READ MORE

CATEGORIES