• 
  What are the effects of axial movement of gear sha

  25-10-24

  The axial movement of the gear shaft will significantly shorten the service life of the RX157-3 reducer, and the core impact is to cause abnormal wear of multiple components and imbalanced load distribution. 1. Accelerate the wear of core components and directly reduce their lifespan Axial movement of the gear shaft can disrupt the originally designed meshing relationship and clearance, leading

  READ MORE
• 
  Detailed installation steps for SCWU140-50-1 worm

  25-10-23

  The detailed installation steps for SCWU140-50-1 worm gear reducer are as follows: 1. Preparation before installation: Equipment inspection: Check whether the packaging of the reducer is intact, whether the appearance is damaged or deformed, and whether the components are complete. Check the nameplate parameters to confirm whether the model, specifications, etc. of the reducer are consistent

  READ MORE
• 
  How to determine if the SCWU280-63 worm gear reduc

  25-10-23

  To determine whether the SCWU280-63 worm gear reducer is installed correctly, it is necessary to start from two aspects: static inspection and dynamic trial operation, and verify whether the installation accuracy, connection reliability, and operational stability meet the requirements. 1、 Static inspection: Verification of installation accuracy and connection reliability Static inspection should

  READ MORE
• 
  How to deal with the scrapped BLD17-29-30KW cycloi

  25-10-22

  After the BLD17-29-30KW cycloidal pinwheel reducer is scrapped, priority should be given to following the principle of "safe disassembly → classified recycling → compliant disposal", which not only avoids environmental pollution but also maximizes the value of recycling and utilization. At the same time, attention should be paid to avoiding safety risks and environmental violations. 1. Preprocess

  READ MORE
• 
  Recommend some installation precautions for BLD19-

  25-10-22

  The installation of BLD19-35-55KW cycloidal pinwheel reducer should focus on the three core aspects of foundation stability, transmission neutrality, and lubrication compliance to avoid operational vibration, component wear, or shortened service life caused by improper installation. Specific precautions can be divided into five key modules. 1. Preparation before installation: Check the equipment

  READ MORE
• 
  How to clean the oil tank of FAF77DV132M4-NA154-7.

  25-10-21

  The cleaning of the oil tank of FAF77DV132M4-NA154-7.5KW reducer should follow the process of "thorough emptying → disassembly and cleaning → flushing and impurity removal → drying inspection". The core is to remove old oil residue, sludge, and metal debris to avoid contaminating new oil. Before operation, it is necessary to ensure that the equipment is shut down and the power is cut off, and the

  READ MORE
• 
  What are the effects of temperature exceeding 80 ℃

  25-10-21

  The impact of temperature exceeding 80 ℃ on the output shaft of WPDKS100-25-1.1KW worm gear reducer can be divided into the following aspects: 1、 Damage to core transmission components Worm gear meshing failure High temperature can cause local melting of the copper worm gear (ZCuSn10Pb1) tooth surface and bonding with the steel worm gear. If it continues for more than 30 seconds, irreversible

  READ MORE
• 
  What is the high temperature warning value set for

  25-10-20

  The setting of high temperature warning values for FAF77-2.2KW-25.47-M5 gear reducer needs to be combined with its structural characteristics and working environment. The core parameters are as follows: 1、 Temperature warning threshold setting Bearing temperature warning value Under normal operating conditions, it is recommended to set the temperature to 75 ℃ (Level 1 warning). If the tempe

  READ MORE
• 
  What are the characteristics of abnormal noises ca

  25-10-20

  The abnormal noise caused by installation deviation of WHS160-8-I worm gear reducer has the following typical characteristics, which need to be analyzed in combination with specific deviation types: 1、 Abnormal noise caused by coaxiality deviation High frequency vibration and noise When the coaxiality of the input/output shaft exceeds the tolerance (radial deviation>0.05mm or angular deviatio

  READ MORE

CATEGORIES