• 
  How to solve the problem of excessive vibration in

  25-06-26

  To solve the problem of excessive vibration in the ZFY800-400-I gearbox body, we can start from the following aspects: 1. Check the installation status Foundation and Connection: Check if the foundation is stable, if there are any settlement, cracks, or other issues, if the anchor bolts are loose, tighten the loose bolts, replace damaged bolts in a timely manner, and if there are any problem

  READ MORE
• 
  The standard range of vibration for the housing of

  25-06-26

  The vibration standard range of ZFY710-280-2 gearbox body is affected by various factors, as follows: 1. Installation situation Foundation stability: An unstable foundation, such as insufficient stiffness or foundation settlement, can cause significant vibrations in the gearbox during operation, leading to changes in the vibration standard range. For example, when installed on a weak steel s

  READ MORE
• 
  What are the factors related to the hazards of loo

  25-06-25

  The hazards of bolt loosening in RX107-3.5-30KW hard tooth gear reducer are related to the following factors: Degree of looseness: When the bolt is slightly loose, it may only cause slight vibration and noise in the gearbox, with little impact on equipment operation. But if the bolts are severely loose, it will cause the connection of the components to be unstable, leading to increased vibratio

  READ MORE
• 
  What are the warning signs of bolt loosening for t

  25-06-25

  The loosening of bolts in GRX77-1.5KW-4P-5.63 hard tooth gear reducer may have the following signs: Abnormal noise: Loose bolts can cause loose connections between internal components of the gearbox, resulting in abnormal noises such as clicking or metal collision during operation. Increased vibration: Loose bolts can cause significant vibration or shaking of components, leading to an increa

  READ MORE
• 
  What regular checks can be performed on the KAZ107

  25-06-24

  To prevent major repairs to the KAZ107-14.43-37KW-M3 gearbox, the following inspections can be conducted regularly: Lubrication system inspection Oil level check: Observe the oil level through the oil gauge every week or before each start-up to ensure that the oil level is between the upper and lower limits. If it is insufficient, replenish it in a timely manner. Oil condition detection:

  READ MORE
• 
  How to adjust the gear mesh clearance of the KAZ47

  25-06-24

  Here are some methods to adjust the gear mesh clearance of KAZ47-Y1.5-19.58-M3-A hard tooth surface gear reducer: Gasket adjustment method: Principle: By increasing or decreasing the number and thickness of shims between the gear and the bearing, the relative position of the gear can be changed to adjust the gear mesh clearance. Operation steps: First, disassemble the relevant components

  READ MORE
• 
  What types of sealing structures are typically fou

  25-06-23

  The common types of sealing structures for ZQA400-IV-1/2 soft tooth surface gear reducers are as follows: 1. Felt ring seal: compact installation size, low technical requirements for disassembly and assembly, and low cost. But the wear is fast, the requirement for the linear speed of the shaft cannot be too high, and the service life is short. It is now less commonly used for shaft end sealing

  READ MORE
• 
  List some factors that may affect the quality of t

  25-06-23

  The following are some factors that may affect the quality of SAF62-Y4-16.17-M1B-0 gear reducer: 1. Material selection: Gear material: High quality gear materials should have high strength, high hardness, good wear resistance and corrosion resistance, as well as good toughness and weldability. If inferior materials are used, gears are prone to wear, deformation, fracture and other problems,

  READ MORE
• 
  When the working environment temperature of the re

  25-06-20

  When the working environment temperature of the reducer is higher than 60 ℃, the following cooling measures can be taken: Improve ventilation conditions Increase air circulation: Ensure sufficient space around the reducer to avoid being surrounded by debris accumulation, and reserve at least 50cm of heat dissipation space. Exhaust fans or ventilation ducts can be installed in the workshop to

  READ MORE

CATEGORIES