• 
  How to select the appropriate nitriding process fo

  25-08-04

  To choose a suitable nitriding treatment process for DCYK250-20-3 gear reducer, the following aspects need to be considered: Gear material: The gears of DCYK250-20-3 gear reducer are usually made of medium carbon steel or medium carbon alloy steel, such as 40Cr, 42CrMo, etc. If steel containing alloy elements such as Al, Cr, Mo, etc. is used, such as 38CrMoAl, it is more conducive to forming hi

  READ MORE
• 
  What specific effects does nitriding treatment hav

  25-08-04

  Nitriding treatment has the following specific effects on the performance of DCYK280-22.4-II gear reducer: Improving hardness and wear resistance: By infiltrating nitrogen atoms into the surface of the gear, a high hardness nitride layer is formed, which can significantly increase the surface hardness of the gear, such as reaching HV600 or above, effectively resist friction and wear between too

  READ MORE
• 
  When adjusting the eccentric bushing of the XLED81

  25-08-02

  When adjusting the eccentric sleeve of XLED8115A-377-0.37KW cycloidal reducer, the following are some precautions: 1. Preparation work: Prepare the necessary tools in advance, such as suitable wrenches, vernier calipers, dial gauges and other measuring tools, as well as cleaning supplies, lubricants, etc. At the same time, it is necessary to ensure that the workplace is clean and tidy, free fro

  READ MORE
• 
  How to repair the broken output shaft of BWE2218-3

  25-08-02

  After the output shaft of BWE2218-391 cycloidal pinwheel reducer breaks, it can be repaired according to the following steps: 1. Preparation before maintenance: Safety measures: Cut off the power supply, hang a warning sign to prevent accidental power on. Ensure that maintenance personnel are familiar with safety operating procedures and wear protective equipment. Tools and materials: Pre

  READ MORE
• 
  What factors may cause a shortened maintenance cyc

  25-07-31

  The following factors may lead to a shortened maintenance cycle for the RX91-4.85-7.5KW gearbox: Poor working environment High temperature: The suitable operating temperature for reducers is generally between -40 ℃ and 45 ℃. If the ambient temperature is too high for a long time, it may lead to increased wear of gears and bearings, reduced effectiveness of lubricating oil, and even deformati

  READ MORE
• 
  How to improve the operating conditions of RXF67-3

  25-07-31

  Improving the operating conditions of the RXF67-3KW-6.08 hard tooth surface gear reducer can be approached from the following aspects: Correct installation and alignment: During installation, ensure that the concentricity deviation between the input shaft of the reducer and the motor shaft, as well as the output shaft and the load shaft, is less than 0.05mm. It is recommended to use a laser ali

  READ MORE
• 
  How to replace the gears of the CWS280-63-IVF worm

  25-07-30

  To replace the gears of the CWS280-63-IVF worm gear reducer, please refer to the following steps: 1. Preparation work: Ensure that the equipment completely stops running, cut off the power, and hang a "Do Not Close" warning sign. After the oil temperature cools down, unscrew the oil drain plug at the bottom of the reducer and collect the old gear oil. Wipe the surface of the shell with cleaning

  READ MORE
• 
  What are the factors that affect the noise level o

  25-07-30

  The main factors affecting the noise level of WPO100-60-B worm gear reducer are as follows: Gear related factors Gear wear and damage: Long term operation can cause gear wear, tooth surface damage, resulting in unstable meshing between gears, increased vibration, and the generation of loud noise. Gear accuracy: Gear accuracy is an important indicator of noise level. The higher the precisi

  READ MORE
• 
  How to ensure the normal operation of the CWU100-8

  25-07-29

  To ensure the normal operation of CWU100-8.3-3 worm gear reducer, it is necessary to start from multiple aspects such as installation, lubrication, operation monitoring, maintenance, etc., as follows: Correct installation Basic fixation: Ensure that the installation base of the reducer is flat and firm, and the anchor bolts need to be tightened to prevent vibration and displacement caused by

  READ MORE

CATEGORIES